Emulex LightPulse LPe1105-M4 HBA Przewodnik Instalacji Strona 138
- Strona / 182
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
138
EMC Host Connectivity with Emulex FC HBAs and FCoE CNAs for the Linux Environment
Configuring a Boot Device on an EMC Storage Array
Although EMC does not make recommendations on the installation
selections, it is worthwhile to create a boot diskette for the installation
to aid in troubleshooting possible connectivity problems.
On completion of the installation, the system will boot into the RHEL
OS selected.
Installing RHEL 3.0 U4 and U5 onto the EMC storage device with the Emulex
v7.x-Series driver
The Emulex v7.1.14 driver ships as the default in both RHEL 3.0 U4
(v2.4.21-27.EL kernel) and U5 (v2.4.21-32.EL kernel).
As of the date this document was written, booting from the SAN is
supported with RHEL 3.0 U4 and U5 for 32-bit, AMD64, and EM64T
architectures, but not Itanium. Refer to the EMC Support Matrix for
the latest information on supported distributions, kernels, and
architectures.
Since the Emulex v7.1.14 driver is integrated into the RHEL 3.0 U4
and U5 kernels, there is no need to create a driver diskette image.
Before beginning the installation, performs the steps described in the
appropriate section for the EMC storage array being used:
◆ “Configuring a Symmetrix boot device” on page 128
◆ “Configuring a VNX series or CLARiiON boot device” on
page 132
Using the RHEL 3.0 U4 CDs, boot the server to be installed. The
installation may now be performed as it would when using an
internal disk drive.
Installing RHEL 3.0 U6 through RHEL 3.9 onto the EMC storage device with the
Emulex v7.x-Series driver
RHEL 3.0 U6 through RHEL 3.9 ship with the Emulex v7.3.x driver as
the default driver in the kernel, refer to Table 5 on page 52 for the
appropriate version.
As of the date this document was written, booting from the SAN is
supported with RHEL 3.0 U6 through RHEL 3.9 for 32-bit, AMD64,
and EM64T architectures, but not Itanium. Refer to the EMC Support
Matrix for the latest information on supported distributions and
architectures.
- -508-435-1000 1
- Contents 3
- Emulex Driver 4
- Chapter 8 Additional Notes 6
- ◆ Linux operating environment 9
- ◆ Emulex adapters and drivers 9
- Courier italic 11
- Introduction 13
- Purpose of this document 14
- Host connectivity 14
- Boot device support 15
- Installation Steps 19
- Linux distribution of choice 21
- Summary of installation steps 22
- Installing the adapter 24
- Adapter edge connectors 28
- PCI Express slots 29
- PCI Express slots aligned 29
- Installing and 31
- Configuring the BIOS 31
- Settings 31
- LP1102 Emulex banner 32
- Updating the boot BIOS 33
- LP6DUTIL.EXE) 37
- LP6DUTIL.EXE program file 37
- 7.x driver) 38
- Installing and 43
- Configuring the Linux 43
- Host with the Emulex 43
- SLES 9, SLES 10, and SLES 11 52
- /sys filesystem 58
- ...Restoring 83
- Cleaning up 86
- ./hbanyware 86
- * If PEMC owerPath 88
- ◆ Miracle Linux v4.0 92
- ◆ RedFlag DC Server 5.0 92
- 4 and RHEL 5” on page 91 93
- Updating the Adapter 97
- Firmware 97
- FCoE adapters 102
- Connecting to the 109
- Planning procedure 110
- Enabling persistent binding 111
- Connecting to the Storage 112
- Editing /etc/modules.conf 114
- Network Settings window 117
- Configuring a Boot 121
- Device on an EMC 121
- Storage Array 121
- Limitations 124
- /dev/sda by the Linux 125
- Preparing the host 128
- CLARiiON 136
- Emulex v7.x-Series driver 138
- Application Kit 141
- Do you have a driver disk 142
- Driver Update OK 143
- Upgrading the Linux kernel 145
- Additional Notes 147
- Rebooting the host 151
- HPQ server-specific note 155
- Block device file names 157
- Red Hat distributions 158
- SuSE distributions 158
- PowerPath examples 159
- Character device file names 159
- Echoing the /proc filesystem 163
- Rescanning the SCSI bus 164
- Special Instructions 167
- For example: 170
- 3. Reboot the host 170
- • For SuSE distributions use: 173
- Example: 173
- 4. Reboot the host 173
- 2.1 Intel Itanium systems 178
- 3.0 Intel Itanium systems 179
Powiązane produkty i podręczniki dla Oprogramowanie Emulex LightPulse LPe1105-M4 HBA
Oprogramowanie Emulex LP21000 Instrukcja Użytkownika
(274 strony)
(274 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.111 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji