Emulex 110 Przewodnik Instalacji Pobierz pdf (Strona 137)

Fibre Channel over Ethernet (FCoE) Converged Network Adapter (CNA) procedures

137

Installation and Configuration

Figure 113 Driver installation window

After the installation is complete, an AutoPilot Installer Warning

message displays, as shown in Figure 114 on page 138.

1 2 ... 132 133 134 135 136 137 138 139 140 141 142 ... 239 240

Windows Environment 1
Contents 3
Chapter 3 Troubleshooting 5
Title Page 13
Installation and 19
Configuration 19
How this guide works 20
Installing the adapter 22
◆ PCI-X 2.0 24
◆ PCI-Express 24
Adapter edge connectors 25
PCI Express slots 26
CDC392a2.awc) 30
Table 2 Firmware filenames 31
LP6DUTIL main screen 34
LP6DUTIL flash menu 35
Selecting the adapter to load 36
LP6DUTIL.EXE tool 36
Change Boot BIOS State window 37
Figure 11 Emulex banner 39
Adapter configuration options 41
Enabling/disabling an adapter 41
Setting the PLOGI retry timer 42
Saved boot devices 43
Firmware boot manager menu 48
Device mapping table 49
Directory listing 50
Current topology setting 57
Figure 39 Targets 60
Boot device identification 62
— This can be 63
Figure 58 Targets 75
Existing partitions 84
Windows Boot Manager 87
Windows Setup screen 87
Windows Install screen 88
Windows 90
Loading driver screen 91
Browse for Folder screen 92
A as shown in Figure 73 92
Install Windows screen 95
Limitations 97
EMC support 97
Emulex HBAnyware utility 98
Pre-installation guidelines 99
Installation complete 103
AutoPilot installer program 104
5. Select Next to continue 105
Topology selection 107
Completing the installation 108
Installer\reports 109
HBAnyware: General tab 110
HBAnyware: Firmware tab 111
Adapter BIOS upgrade 113
Adapter (CNA) procedures 117
Device Manager 118
HBAnyware utility 119
Figure 98 121
Maintenance tab 122
Confirmation dialog box 123
Firmware Download window 124
Figure 104 Options 127
CEE ta b 128
Warning dialog box 129
Start Download 130
Progress bar 131
Installation completed window 135
AutoPilot Installer window 136
Driver installation window 137
Firmware tab 141
Firmware file location 142
Download Firmware dialog box 145
CNA adapters 146
Enable the adapter 149
List of Saved Boot Devices 150
Setting the primary boot LUN 151
Selecting the boot method 154
Reboot message 154
OCe10102-IM iSCSI adapters 155
Enable Boot Support 158
Controller Static IP Address 159
Adding iSCSI Target 161
Channel adapter 169
ElxSec Setup Wizard 172
Config.bat 176
Emulex NPIV solution 179
Miscellaneous Planning 181
Downloading the driver 183
Installing the adapter driver 183
EMC Support Matrix 184
STORPort drivers 185
A:\, for 190
Blade server restrictions 193
ELXCFG.EXE 195
Changing the configuration 205
Version 1.41a2 options 207
Preconfigured settings 208
Maximum Number of LUNs 208
MSCS with tape devices 209
Emulex configuration tool 212
Set the adapter FC-AL Loop ID 218
Troubleshooting 221
Basic troubleshooting steps 222
Volume sizes 227
Host after the rebooted 230
Understanding queue depth 231
Known issues 233
Problems and solutions 235
Problem 5 236
Problem 6 236
Problem 7 236
Problem 8 236
Third-Party Software 239
Emulex HBAnyware 240

Komentarze do niniejszej Instrukcji

Brak uwag

Emulex 110 Przewodnik Instalacji Strona 137

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Emulex 110