Emulex LP9802DC Instrukcja Użytkownika Strona 1

Downloading the Emulex Driver for NetWareVersion 2.10cTable of ContentsPrerequisitesCompatibilityThings to Know Before You DownloadChanges and Correct

EMULEX END USER LICENSE AGREEMENTAny software and documentation provided hereunder (respectively "Software" and "Documentation") a

Installing the Emulex Driver for NetWareVersion 2.10cTable of ContentsDriver InformationInstall Driver on New Netware ServerInstall Driver on Existing

Install Driver on a New NetWare ServerNetWare files may be installed on a Fibre Channel disk provided a boot disk withDOS exists.Follow the standard N

Install Driver on an Existing NetWare ServerAt the server console:Load the install program by entering the following command:LOAD NWCONFIG1. Select &q

Configuring the Emulex Driver for NetWareVersion 2.10cTable of ContentsIntroductionDriver ParametersSpecial Command Line ParametersEmulex Drivers, Sof

IntroductionOptions in the following Driver Parameter and Special Command Line Parameterpages can be configured to "fine tune" the Emulex SC

Driver ParametersALPA (Arbitrated Loop Port Address)This parameter selects the AL_PA that the adapter requests during the loopinitialization. The AL_P

LINK_DOWN_TOUTMinimum value = 0, maximum value = 65536 (decimal). Default = 60;This parameter specifies the maximum time, in seconds, for a link to re

NUMBDESMinimum value = 2000, maximum value = 5000 (decimal). Default = 4000;This parameter allows resources to be tuned for the number of devices. Eac

RSCNDELAYMinimum value = 0, maximum value = 60 (decimal). Default = 0;RSCNDELAY specifies the time, in seconds, to delay a query to the Fibre ChannelN

Driver InformationPrerequisitesNetWare 6.0 with Support Pack 2 (SP2) or Support Pack 3 (SP3) andNW56UP2 and NW6NSS2D patches.Note If you are running N

DELAY_TOUTMinimum value = 0, maximum value = 500 (decimal). Default = 0;This parameter specifies a delay period to extend the timeout value of operati

Special Command Line ParametersThe command line parameters on this page are parsed separately from the rest ofthe command line parameters. Install−tim

The last two forms allow the parameter to refer to a specific LUN or range ofLUNs.When several devices with similar names are to be specified, an aste

BINDWWPN − This parameter configures the driver to recognize a specific device with aspecific SCSI ID used to identify it to the system, using the Wor

REJECTWWPN − This parameter configures the driver to ignore a specific device, using the WorldWide Port Name for the device as the key to identifying

Things to Know Before You DownloadBefore you download, create a temporary directory for the Netwaredriver kit.• NetWare files may be installed on a Fi

Changes and CorrectionsThe driver supports up to sixteen adapter channels using single or dualchannel host bus adapters. In version 2.03c, the driver

Known IssuesA small percentage of unload attempts of a single adapter may cause amirrored partition supported by another adapter to be dismounted.• If

Files Included in this ReleaseThis kit includes the following files.File Name Descriptionreadme.txt Release notes for Netware Version 2.10clpfc.ham Em

Verifying Dragonfly Chip VersionThere are three methods for determining the Dragonfly chip version:Looking at the Host Bus Adapter, running the DOS ut

Select 3, Adapter Revision Levels . If there are multiple host adapters,specify a list of numbers from 1 – 3 separated by spaces, or use a '–&apo

Select 2, Adapter Information. The Adapter Information Menu is displayed.2. Select 2, Adapter Revision Levels. If there are multiple host adapters, a